LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2015 >> Regal GS, AWD >> Repair and Diagnosis >> Accessories & Equipment >> Drivers Assistance Systems - ADAS >> Object Detection And Pedestrian Protection System >> Diagnostic Information and Procedures >> DTC B0967 or B0968: Parking Assist On/Off Switch/Indicator >> Circuit/System Testing

Circuit/System Testing

Parking Assist Switch Malfunction

  1. Ignition OFF, disconnect the harness connector at the S48D Multifunction Switch 2 - Instrument Panel.
  2. Test for less than 10Ω between the S48D Multifunction Switch 2 - Instrument Panel terminal 1 and ground.
    • If 10Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2Ω in the ground circuit end to end.
      • If 2Ω or greater, repair the open/high resistance in the ground circuit.
      • If less than 2Ω, repair the open/high resistance in the ground connection.
    • If less than 10Ω 
  3. Connect a test lamp between the control circuit terminal 5 and ground circuit terminal 1.
  4. Verify the test lamp turns On and Off when commanding the Parking Assist Switch On and Off with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the harness connector at the K41R Rear Parking Assist Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground in the circuit.
      • If infinite resistance
    3. Test for less than 2Ω in the control circuit end to end.
      • If 2Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2Ω, replace the K41R Rear Parking Assist Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the harness connector at the K41R Rear Parking Assist Control Module, ignition ON.
    2. Test for less than 1V between the control circuit and ground.
      • If 1V or greater, repair the short to voltage on the circuit
      • If less than 1V, replace the K41R Rear Parking Assist Control Module.
    • If the test lamp turns ON and OFF 
  5. All OK.

Parking Assist Switch Indicator Malfunction

  1. Ignition OFF, disconnect the harness connector at the S48D Multifunction Switch 2 - Instrument Panel.
  2. Test for less than 10Ω between the S48D Multifunction Switch 2 - Instrument Panel terminal 1 and ground.
    • If 10Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2Ω in the ground circuit end to end.
      • If 2Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2Ω, repair the open/high resistance in the ground connection.
    • If less than 10Ω 
  3. Connect a test lamp between the voltage circuit terminal 6 and ground circuit terminal 1.
  4. Verify the test lamp turns ON and OFF when Commanding the Parking Assist Switch On and Off with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the harness connector at the K41R Rear Parking Assist Control Module.
    2. Test for infinite resistance between the voltage circuit and ground.
      • If less than infinite resistance, repair the short to ground in the circuit.
      • If infinite resistance
    3. Test for less than 2Ω in the control circuit end to end.
      • If 2Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2Ω, replace the K41R Rear Parking Assist Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the harness connector at the K41R Rear Parking Assist Control Module, ignition ON.
    2. Test for less than 1V between the voltage circuit and ground.
      • If 1V or greater, repair the short to voltage on the circuit.
      • If less than 1V, replace the K41R Rear Parking Assist Control Module.
    • If the test lamp turns ON and OFF 
  5. All OK.
scientia non olet · About LEMON Manuals