LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2013 >> Verano Base >> Repair and Diagnosis >> Body & Frame >> Windows >> Fixed And MOVEABLE Window System >> Diagnostic Information and Procedures >> Rear Window Defogger Malfunction >> Circuit/System Testing

Circuit/System Testing

  1. Ignition OFF and all vehicle systems OFF, disconnect the KR5 Rear Defogger Relay. It may take up to 2 minutes for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 1 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Connect a test lamp between the control circuit terminal 2 and the ground circuit terminal 1. Engine running
  4. Verify the test lamp turns ON and OFF when commanding the Rear Defogger On and Off with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the harness connector at the K33 HVAC Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K33 HVAC Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the harness connector at the K33 HVAC Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K33 HVAC Control Module.
    • If the test lamp turns ON and OFF 
  5. Verify that a test lamp does not illuminate between the control circuit terminal 5 and ground.
    • If the test lamp illuminates 

      Repair the short to voltage on the control circuit

    • If the test lamp does not illuminate 
  6. Ignition OFF and all vehicle systems OFF, disconnect the X2 harness connector at the E18 Rear Defogger Grid. It may take up to 2 minutes for all vehicle systems to power down.
  7. Test for less than 10 Ω between the ground circuit terminal 1 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  8. Connect the X2 harness connector at the E18 Rear Defogger Grid.
  9. Ignition ON, connect a 40 A fused jumper wire between the B+ circuit terminal 3 and the control circuit terminal 5.
  10. Verify the E18 Rear Defogger Grid is activated.
    • If the E18 Rear Defogger Grid does not activate 
    1. Ignition OFF, disconnect the X1 harness connector at the E18 Rear Defogger Grid.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, test or replace the E18 Rear Defogger Grid.
    • If the E18 Rear Defogger Grid activates 
  11. Test or replace the KR5 Rear Defogger Relay.
scientia non olet · About LEMON Manuals