Common Specs & Procedures Index

LACROSSE COMMON SPECS & PROCEDURES

System		Specification/Procedure
Air Conditioning
Service		REFRIGERANT SYSTEM SPECIFICATIONS
Torque		Automatic - FASTENER TIGHTENING SPECIFICATIONS
Axle Nut/Hub Nut
Front & Rear		Fist Pass - 111 lb ft (150 N.m) Second Pass - Loosen 45 degrees Final Pass - 184 lb ft (250 N.m)
Battery		Hybrid - BATTERY USAGE Except Hybrid - BATTERY USAGE
Brakes
Bleeding Sequence		Manual - RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) . Pressure - RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT. See HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) .
Disc Brakes
	Service Specifications	DISC BRAKE COMPONENT SPECIFICATIONS
	Torque	FASTENER TIGHTENING SPECIFICATIONS
Drum Brakes
	Service Specifications	N/A
	Torque	N/A
Charging
Generator		Hybrid - N/A Except Hybrid - GENERATOR USAGE
Torque		Hybrid - N/A Except Hybrid - FASTENER TIGHTENING SPECIFICATIONS
Drive Belts
Adjustment		Hybrid - Serpentine belt used, not adjustable. Except Hybrid - Serpentine belt used, not adjustable.
Drive Belt Routing		Hybrid - See the figure under DRIVE BELT REPLACEMENT . Except Hybrid - See the figure under Drive Belt Replacement (Without EPS) , or DRIVE BELT REPLACEMENT (WITH EPS) .
Engine Cooling
General Service Specifications		N/A
	Radiator Cap Pressure	Pressure stamped on cap.
	Thermostat R & I
	2.4L - Hybrid	ENGINE COOLANT THERMOSTAT REPLACEMENT (LUK)
	3.6L - Except Hybrid	ENGINE COOLANT THERMOSTAT REPLACEMENT (V6)
	Water Pump R & I
	2.4L - Hybrid	WATER PUMP REPLACEMENT (LFX)
	3.6L - Except Hybrid	WATER PUMP REPLACEMENT (L4)
Engine Mechanical
2.4L - Hybrid
	Compression	ENGINE COMPRESSION TEST
	Oil Pressure	Minimum @ 1000 RPM @ 90°C (194°F)
	Overhaul	ENGINE MECHANICAL SPECIFICATIONS (LAF, LEA, OR LUK)
	Torque	FASTENER TIGHTENING SPECIFICATIONS (LAF, LEA, OR LUK)
3.6L - Except Hybrid
	Compression	ENGINE COMPRESSION TEST
	Oil pressure	Minimum @ Idle - 69 kPa (10 psi) Minimum @ 2, 000 - 138 kPa (20 psi)
Overhaul		ENGINE MECHANICAL SPECIFICATIONS (LFX)
	Torque	FASTENER TIGHTENING SPECIFICATIONS
Fluid Specifications		See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate/Drive Plate Torque		Hybrid First Pass - 39 lb ft (53 N.m) Final Pass - Additional 25 degrees Except Hybrid First Pass - 22 lb ft (30 N.m) Final Pass - Additional 45 degrees
Fuel System
Pressure Specification		Hybrid Not Running - 345-690 kPa (50-100 psi) See CIRCUIT/SYSTEM VERIFICATION . Except Hybrid Not Running - 345-690 kPa (50-100 psi) See CIRCUIT/SYSTEM VERIFICATION .
	Fuel Pressure Test Procedure	Hybrid - FUEL SYSTEM DIAGNOSIS Except Hybrid - FUEL SYSTEM DIAGNOSIS
	Fuel Filter Location	Hybrid - Fuel filter is part of the fuel tank fuel pump module. Except Hybrid - Fuel filter is part of the fuel tank fuel pump module.
	Fuel Filter R & I	Hybrid See FUEL TANK FUEL PUMP MODULE REPLACEMENT (NT7) or FUEL TANK FUEL PUMP MODULE REPLACEMENT (NU6) . Except Hybrid See FUEL TANK FUEL PUMP MODULE REPLACEMENT (LFW OR LFX) or FUEL TANK FUEL PUMP MODULE REPLACEMENT (WITH AWD) .
Ignition
Firing Order & Cylinder Identification		FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance)		Hybrid - Individual Ignition Coil/Module Assemblies. Except Hybrid - Individual Ignition Coil/Module Assemblies.
Ignition Wires (Routing)
Hybrid		Coil on plug.
Except Hybrid		Coil on plug.
Spark Plug
Hybrid (Refer to Electronic Parts Catalogue for Spark Plug Type)
	Gap	0.035 in (1.0 mm)
	Torque	15 lb ft (20 N.m)
Except Hybrid (Refer to Electronic Parts Catalogue for Spark Plug Type)
	Gap	0.043 in (1.1 mm)
	Torque	15 lb ft (20 N.m)
Starting
Starter		Hybrid - N/A Except Hybrid - N/A
Torque		FASTENER TIGHTENING SPECIFICATIONS
Wheel Alignment
	Adjustment Specifications	WHEEL ALIGNMENT SPECIFICATIONS
	Torque	FASTENER TIGHTENING SPECIFICATIONS
Wheel & Tire
Wheel Lug Nut Torque		110 lb ft (150 N.m) For tightening sequence, please see the figure under INSTALLATION PROCEDURE .