Engine Electrical System -- Repair (F96)

• 12 00 General Information
  • Instructions for removal and replacement of control units (X6 M 2020-2023)
  • Notes on starting assistance (X6 M 2020-2023)
• 12 12 Spark Plugs
  • 12 12 011 Removing and installing/replacing all spark plugs (X6 M 2020-2023)
    • Removing all spark plugs of cylinder bank 1
    • Removing all spark plugs of cylinder bank 2
    • Installing all spark plugs of cylinder bank 2
    • Installing all spark plugs of cylinder bank 1
• 12 13 Ignition Coils
  • 12 13 506 Replacing an ignition coil, right (following vehicle diagnosis) (X6 M 2020-2023)
    • Removing ignition coil of cylinder bank 1
    • Install ignition coils of cylinder bank 1
  • 12 13 507 Replacing an ignition coil, left (after vehicle diagnosis) (X6 M 2020-2023)
    • Removing ignition coil of cylinder bank 2
    • Install the ignition coils of cylinder bank 2
• 12 14 Crankshaft Sensor, Camshaft Sensor, Knock Sensor, Engine Control Module
  • 12 14 512 Replace left exhaust camshaft sensor (after vehicle diagnosis) (X6 M 2020-2023)
    • Removing the left camshaft position sensor of the exhaust camshaft
    • Install the left camshaft position sensor of the exhaust camshaft
  • 12 14 513 Replace right exhaust camshaft sensor (after vehicle diagnosis) (X6 M 2020-2023)
    • Removing the camshaft position sensor of the exhaust camshaft on the right
    • Installing the camshaft position sensor of the right exhaust camshaft
  • 12 14 521 Replacing the crankshaft sensor (after vehicle diagnosis) (X6 M 2020-2023)
    • Removing the crankshaft sensor
    • Installing the crankshaft sensor
  • 12 14 522 Replace left intake camshaft sensor (after vehicle diagnosis) (X6 M 2020-2023)
    • Removing the intake camshaft sensor of cylinder banks 5 to 8
    • Installing the intake camshaft sensor of cylinder banks 5 to 8
  • 12 14 526 Replace right intake camshaft sensor (after vehicle diagnosis) (X6 M 2020-2023)
    • Removing intake camshaft sensor of cylinder bank 1
    • Installing intake camshaft sensor of cylinder bank 1
  • 12 14 555 Replacing the engine control module (DME), cylinder 1-4 (after vehicle diagnosis) (X6 M 2020-2023)
    • Removing the DME control unit for cylinders 1 to 4
    • Installing the DME control unit for cylinders 1 to 4
  • 12 14 556 Replacing the engine control module (DME), cylinder 5-8 (after vehicle diagnosis) (X6 M 2020-2023)
    • Removing the DME control unit for cylinders 5 to 8
    • Installing the DME control unit of cylinders 5 to 8
  • 12 14 610 Replacing knock sensor(s) right (X6 M 2020-2023)
    • Remove the knock sensors on the right
    • Install the knock sensors on the right
  • 12 14 611 Replace the left knock sensor(s) (after vehicle diagnosis) (X6 M 2020-2023)
    • Remove the left knock sensors
    • Installing the left knock sensors
  • 12 14 700 Coding the control unit (DME) (X6 M 2020-2023)
  • 12 14 705 Programming the control unit (DME) (X6 M 2020-2023)
• 12 31 Alternator
  • 12 31 020 Removing and installing/replacing alternator (X6 M 2020-2023)
    • Removing the alternator
    • Install alternator
• 12 32 Voltage Regulator For Alternator
  • 12 32 501 Replacing the voltage regulator for the alternator (after vehicle diagnosis) (X6 M 2020-2023)
    • Replacing the alternator speed governor
• 12 41 Starter Motor
  • 12 41 020 Removing and installing/replacing starter motor (X6 M 2020-2023)
    • Removing starter motor
    • Installing starter motor
  • 12 41 041 Replacing the engagement solenoid switch (X6 M 2020-2023)
• 12 42 Starter Motor Positive Battery Cable
  • 12 42 500 Removing and installing/replacing the positive battery cable (X6 M 2020-2023)
    • Removing positive battery cables
    • Install positive battery cable
  • 12 42 540 Replacing the safety battery terminal (SBK) (X6 M 2020-2023)
• 12 51 Wiring Harness For Engine And Transmission
  • 12 51 245 Remove and install/replace transmission module engine wiring, (X6 M 2020-2023)
    • Remove the transmission wiring harness
    • Installing transmission wiring harness
  • 12 51 300 Remove and install/replace engine wiring harness section, ignition module cylinder 1-4 (X6 M 2020-2023)
    • Removing wiring harness section for the ignition system of cylinder bank 1
    • Installing wiring harness section for ignition system of bank 1
  • 12 51 301 Remove and install/replace engine wiring harness section, ignition module cylinder 5-8 (X6 M 2020-2023)
    • Remove wiring harness section for the ignition system of cylinder bank 2
    • Installing wiring harness section for ignition system of bank 2
  • 12 51 302 Remove and install/replace wiring harness section, sensor system module cylinder 1-4 (X6 M 2020-2023)
    • Removing the wiring harness for the sensor system of cylinder bank 1
    • Installing wiring harness for sensor system of cylinder bank 1
  • 12 51 303 Remove and install/replace wiring harness section, sensor system module cylinder 5-8 (X6 M 2020-2023)
    • Removing wiring harness section of sensor system 5-8
    • Installing the wiring harness section for sensor system 5-8
  • 12 51 304 Remove and install/replace wiring harness section of the Valvetronic servomotor of cylinders 1-4 (X6 M 2020-2023)
    • Removing the wiring harness section of Valvetronic servomotor of cylinders 1 to 4
    • Installing the wiring harness section for the Valvetronic servomotor of cylinders 1 to 4
  • 12 51 305 Remove and install/replace wiring harness section of the Valvetronic servomotor of cylinders 5-8 (X6 M 2020-2023)
    • Removing the wiring harness section for the Valvetronic servomotor of cylinders 5 to 8
    • Installing the wiring harness section of the Valvetronic servomotor of cylinders 5 to 8
  • 12 51 321 Removing and installing/replacing adapter between the wiring harness section and the oil level sensor (X6 M 2020-2023)
    • Removing adapter cable for oil-level sensor
    • Install adapter cable of the oil-level sensor
  • 12 51 322 Removing and installing/replacing wiring harness section of the engine control module (DME/PDM) (X6 M 2020-2023)
    • Removing the wiring harness section of the DME for the integrated power supply module
    • Installing the wiring harness section of DME for integrated power supply module
  • 12 51 323 Removing and installing/replacing adapter between the wiring harness section and the oil temperature sensor (X6 M 2020-2023)
    • Remove wiring harness section adapter for oil temperature sensor
    • Install wiring harness section adapter for oil temperature sensor
• 12 52 ECM Holder
  • 12 52 032 Removing and install right control unit bracket (X6 M 2020-2023)
    • Removing the holder for the right-hand DME control unit
    • Installing the holder for the Digital Motor Electronics control unit on the right
  • 12 52 033 Removing and installing/replacing the left control unit bracket (X6 M 2020-2023)
    • Removing the holder for the DME control unit on the left
    • Installing the holder for the DME control unit on the left
• 12 61 Oil Pressure Switch, Oil Level Sensor
  • 12 61 280 Removing and installing/replacing oil pressure switch (X6 M 2020-2023)
    • Removing the oil pressure switch
    • Installing the oil pressure switch
  • 12 61 285 Replacing engine oil level sensor (X6 M 2020-2023)
    • Removing the oil-level sensor
    • Prepare the oil-level sensor
    • Installing the oil-level sensor
• 12 63 Power Distribution Box
  • 12 63 586 Replacing power distribution box (after vehicle diagnosis) (X6 M 2020-2023)
    • Remove the integrated power supply module (PDM)
    • Install the integrated power supply module (PDM)