Installing the engine wiring harness for sensor system 1

Engine wiring harness for sensor system 1 

Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in and install the engine wiring harness (1)  for the sensor system 1.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in and install the engine wiring harness (1)  for the sensor system 1.
• Secure clamps (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1)  and lock.

  The connector (1)  must engage audibly.

• Secure clamp (arrow).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1)  and lock.

  The connectors (1)  must engage audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in and install the charge air line (1)  in arrow direction.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure the clamp (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1)  and lock.

  The connectors (1) must engage audibly.

• Secure the clamps (arrows).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in and install the engine wiring harness (2)  for the sensor system 1.
• Tighten down screws (1)  .
  TIGHTENING TORQUES SPECIFICATION
  
  

  Cable bracket on rear cylinder head/transmission
  M6x20	tightening torque	8 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Guide in the wiring harness section (2)  and install.
• Make sure that the lock (arrow) engages correctly,
• Tighten down screws (1)  .
  TIGHTENING TORQUES SPECIFICATION
  
  

  Cable bracket on rear cylinder head/transmission
  M6x20	tightening torque	8 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1)  and (2)  and lock.

  The connectors (1)  and (2)  must engage audibly.

• Secure clamp (arrow).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1)  and lock.

  The connectors (1)  must engage audibly.

• Secure the clamps (arrows).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1)  and lock.

  The connectors (1)  must engage audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING THE TANK VENT VALVE .
• Refer to INSTALLING CHARGE AIR COOLER .
• Refer to CONNECTING THE COOLANT LINE TO THE RADIATOR .
• Refer to INSTALLING FAN COWL .
• Refer to INSTALLING CONTROL UNIT BRACKET .
• Refer to INSTALLING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
• Refer to INSTALLING THE DME CONTROL UNIT .
• Refer to INSTALLING COVER OF THE DME CONTROL UNIT .
• Refer to INSTALLING THE LEFT AIR DUCT .
• Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
• Refer to INSTALLING FRONT-END STRUT ON LEFT AND RIGHT .
• Refer to INSTALLING FRONT CROSS CONNECTION .
• Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT AND RIGHT .
• Refer to INSTALLING INTAKE FILTER HOUSING .
• Refer to INSTALLING THE STRUT BRACE .
• Refer to INSTALLING THE SECOND END PANEL UNDERNEATH .
• Refer to INSTALLING THE COWL UPPER PART .
• Refer to INSTALLING TENSION STRUT ON SHOCK TOWER .
• Refer to INSTALLING WINDSHIELD PANEL COVER .
• Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
• Refer to INSTALLING THE SEAL FOR THE HOOD GASKET LEFT AND RIGHT .
• Refer to CONNECTING NEGATIVE BATTERY CABLE OF THE SYSTEM BATTERY .
• Refer to INSTALLING THE COVER PANEL OF THE ENGINE COMPARTMENT ON THE REAR LEFT AND RIGHT .
• Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
• Refer to CONNECTING THE COOLANT HOSE TO THE AUXILIARY COOLANT RADIATOR .
• Refer to FILLING AND VENTING THE HIGH-TEMPERATURE COOLANT CIRCUIT .
• Refer to FILLING AND VENTING THE LOW-TEMPERATURE COOLANT CIRCUIT .
• Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE LEFT .
• Refer to INSTALLING THE FRONT SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
• Refer to PARTIALLY INSTALLING BOTH FRONT WHEEL ARCH TRIMS .
• Refer to INSTALLING THE FRONT BOTTOM RIGHT WHEEL ARCH COVER .
• Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
• Refer to INSTALLING FRONT UNDERBODY PROTECTION .