11 61 Intake System
4 CYL. B46/B48 ENGINE:
11 61 INTAKE PLENUM - TIGHTENING TORQUE SPECIFICATIONS
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Intake plenum to cylinder head | B42S20O0/B46M0/O0/B48M0/O0 | M6 | 10 Nm | |
| 2AZ Holder for intake plenum to cylinder head/crankcase | B42S20O0/B46M0/O0/B48M0/O0 | M6 | 10 Nm | |
| 3AZ Rear intake plenum holder | B42S20O0/B46M0/O0/B48M0/O0 | M6 | 10 Nm | |
| 4AZ Intake plenum to rear/front holder | B42S20O0/B46M0/O0/B48M0/O0 | 8 Nm | ||
| 5AZ Holder for wiring harness to intake plenum | B42S20O0/B46M0/O0/B48M0/O0 | 5 Nm | ||
| 6AZ Tank vent line to intake plenum | B42S20O0/B46M0/O0/B48M0/O0 | 5 Nm |
11 61 INTAKE MANIFOLD - TIGHTENING TORQUE SPECIFICATIONS
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Intake manifold to cylinder head | All | M8 | 22 Nm | |
| All | M7 | 15 Nm | ||
| All | M6 | 10 Nm |
4 CYL. N47 (DIESEL) ENGINE:
11 61 INTAKE PLENUM - TIGHTENING TORQUE SPECIFICATIONS
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Intake manifold to cylinder head | N47 D16/20 K/U/O/T 1 | M6x76 M6x114 |
Observe tightening sequence. 1. Joining 2. Final torque |
5 Nm 10 Nm |
| 2AZ Air intake system to exhaust gas recirculation (EGR) cooler | N47 D16/20 K/U/O/T 1 | 1. Joining 2. Final torque |
4 Nm 10 Nm |
11 61 INTAKE MANIFOLD - TIGHTENING TORQUE SPECIFICATIONS
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Intake manifold to cylinder head | All | M8 | 22 Nm | |
| All | M7 | 15 Nm | ||
| All | M6 | 10 Nm |
6 CYL. B58 ENGINE:
1161 INTAKE SYSTEM - TIGHTENING TORQUE SPECIFICATION
| Front/rear support for intake system to engine block | |||
| M6 x 16 | Tightening torque | 10 Nm | |
| Intake plenum to cylinder head | |||
| Observe tightening sequence. | 1. Joining torque | 5 Nm | |
| 2. Tightening torque | 10 Nm | ||
| Intake plenum to rear/front support | |||
| BM6 x 25 | Tightening torque | 10 Nm | |
| Tank vent line to intake plenum | |||
| TS5 x 16 | Tightening torque | 5 Nm | |
| Wiring harness to intake plenum | |||
| Tightening torque | 5 Nm | ||
11 61 INTAKE MANIFOLD - TIGHTENING TORQUE SPECIFICATIONS
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Intake manifold to cylinder head | All | M8 | 22 Nm | |
| All | M7 | 15 Nm | ||
| All | M6 | 10 Nm |