LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2021 >> RS 6 Avant >> Repair and Diagnosis >> Accessories & Equipment >> Entertainment Systems >> Communication >> 91 Communication >> Rearview Camera System >> Rearview Camera System, Calibrating >> Rearview Camera, Calibrating

Rearview Camera, Calibrating

-- Establish the requirements. Refer to Requirements for Calibrating .

-- Connect the Vehicle Diagnostic Tester.

Calibration Tool - Wheel Center Mounting: VAS6350/1A  Installing:

-- Check the dimension of the holes.

-- Equip the Calibration Tool - Wheel Center Mounting: VAS6350/1  appropriately. Use spacer pieces.

-- To do so, secure the three wheel bolt adapters in the hole for each Calibration Tool - Wheel Center Mounting: VAS6350/1A  .

-- Place the paddles on both Calibration Tool - Wheel Center Mountings: VAS6350/1A  and secure them using a clamping screw.

-- Place the Calibration Tool - Wheel Center Mounting: VAS6350/1A  onto the wheel bolts on the rear wheels.

The Calibration Tool - Wheel Center Mountings: VAS6350/1A  are positioned and secured by the "O-rings" in the adapters.

Fig 1: Identifying Wheel Pick-Ups On Wheel Mounting Bolts At Rear Wheels
GWWN94-10685Courtesy of AUDI OF AMERICA, LLC
NOTE:

Attach the Calibration Tool - Wheel Center Mountings: VAS6350/1A  onto the wheels so that any installed "anti-theft" wheel bolts are not connected to the Calibration Tool - Wheel Center Mountings: VAS6350/1A  .

-- Adjust the paddles with the aid of clamping screw so that they move freely just above the floor. Check the paddles for ease of movement.

-- Install and align the Calibration Tool: VAS6350A  . Refer to Calibration Unit .

Distance measurement:

-- Turn on the Calibration Tool - Spacing Laser: VAS6350/2A  . Refer to Calibration Tool - Spacing Laser: VAS6350/2A  Operating Instructions.

-- For distance measurement, hold the Calibration Tool - Spacing Laser: VAS6350/2A  -2- flush to the right catch bracket as shown.

Fig 2: Ensuring Laser Beam From Distance Laser VAS 6350/2 Hits Lower, Enlarged Part Of Paddle
GWWN94-10684Courtesy of AUDI OF AMERICA, LLC

-- Make sure the "laser beam" for the distance measurement contacts the enlarged lower part on the paddle -1-.

If this is not the case, the measuring paddle height must be corrected using the locking nuts on the Calibration Tool - Wheel Center Mounting: VAS6350/1A  .

-- Briefly press the button for the distance measurement. Refer to Calibration Tool - Spacing Laser: VAS6350/2A  Operating Instructions.

-- Note the readout value (specified value: 1.47 m bis 1.90 m).

-- Repeat this measurement on the other side of the Calibration Tool: VAS6350A  in the same way for the rear wheel.

The distance value must be the same on both sides.

If values are not identical:

-- Align the Calibration Tool: VAS6350A  so that the values on both sides are identical.

Pay attention when aligning the Calibration Tool: VAS6350A  that the Calibration Tool - Linear Laser: VAS6350/3A  on the Calibration Tool: VAS6350A  strikes the center above of the Audi rings and the level indicator remains centered. Adjust if necessary.

Dimension measurement -H- :

-- Measure the height of the Calibration Tool: VAS6350A  , dimension -H- (platform top edge - floor).

Fig 3: Identifying Height Of Calibration Platform, Dimension -H-
GWWA91-11140Courtesy of AUDI OF AMERICA, LLC

Make sure the Calibration Tool - Spacing Laser: VAS6350/2A  is adjusted correctly. Refer to the Calibration Tool - Spacing Laser: VAS6350/2A  Operating Instructions.

Enter the height and distance dimensions into the Vehicle Diagnostic Tester in "millimeters".

Calibrating Procedure

Connect the Vehicle Diagnostic Tester.

-- Select the Diagnostic  mode and start the diagnosis.

-- Select the Test plan  tab.

-- Select the Select individual test  button and select the following tree structure consecutively:

scientia non olet · About LEMON Manuals