Diagnostic Mode 06 - Read Test Results For Specific Diagnostic Functions, 2015 My: Notes
Diagnostic Mode 06 makes it possible to retrieve test results for special components and systems which are continuously or not continuously monitored. If the diagnosis of a system is complete, the diagnostic result and the corresponding thresholds are saved and displayed in mode 06. This data remains saved (even with the ignition off) until either new diagnostic results become available or the DTC memory is erased.
The min & max values for each individual test in Mode 06 represent the minimum & maximum operating values for a properly operating system. This data is provided to the individual aftermarket scan tool companies for development of their scan tool. Depending on the scan tool being used, the min & max values shown may vary, or be rounded up or down to the nearest decimal point depending on the aftermarket scan tool company's development process. e.g.:
| Minimum Value | |
|---|---|
| GST manual documentation | 0.3499 |
| Aftermarket scan tool display | 0.35 |
Depending on the scan tool and protocol used, the information displayed in diagnostic mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).
Test requirements
- Exhaust system must be properly sealed between the catalytic converter and the cylinder heads.
- No DTCs stored in the DTC memory.
- Coolant temperature at least 80 °C.
Work procedure
-- CONNECT: Scan Tool
-- START ENGINE: Idle
-- SELECT: Mode 06
-- SELECT: Test-ID
The current minimum and maximum values listed below will be displayed on the scan tool screen.
| Monitor-ID | Component or System |
|---|---|
| $01: Monitor-ID $01: Oxygen Sensor Monitor Bank 1 - Sensor 1 | Oxygen Sensor Monitor Bank 1 - Sensor 1 |
| $02: Monitor-ID $02: Oxygen Sensor Monitor Bank 1- Sensor 2 | Oxygen Sensor Monitor Bank 1 - Sensor 2 |
| $20: | Supported OBDMID`s ($21 - $40) |
| $21: Monitor-ID $21: Catalytic Converter Monitoring | Catalytic Converter Monitoring |
| $35: Monitor-ID $35: Camshaft adjustment / IVVT diagnosis bank 1 | Camshaft adjustment / IVVT diagnosis bank 1 |
| $3C: Monitor-ID $3C: Tank ventilation system leak test (0.020" / 0.5mm) | Tank ventilation system leak test (0.020" / 0.5mm) |
| $3D: Monitor-ID $3D: EVAP Valve Function Check | Tank vent valve - function check |
| $40: | Supported OBDMID`s ($41 - $5F) |
| $41: Monitor-ID $41: Oxygen Sensor Heater Monitor Bank 1 - Sensor 1 | Heater exhaust gas sensor 1 - Bank 1 |
| $42: Monitor-ID $42: Oxygen Sensor Heater Monitor Bank 1 - Sensor 2 | Heater exhaust gas sensor 2 - Bank 2 |
| $60: | Supported OBDMID ' s ($61 - $80) |
| $71: Monitor-ID $71: Secondary air injection system bank 1 | Secondary air injection system bank 1 |
| $80: | Supported OBDMID ' s ($81 - $A0) |
| $A0: | Supported OBDMID ' s ($A1 - $C0) |
| $A2: Monitor-ID $A2: Misfire Cylinder 1 Data | Misfire Cylinder 1 Data |
| $A3: Monitor-ID $A3: Misfire Cylinder 2 Data | Misfire Cylinder 2 Data |
| $A4: Monitor-ID $A4: Mis-Fire Cylinder 3 Data | Misfire Cylinder 3 Data |
| $A5: Monitor-ID $A5: Mis-Fire Cylinder 4 Data | Misfire Cylinder 4 Data |