LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2013 >> S7 >> Repair and Diagnosis >> Quick Lookups >> DTC Index >> Diagnostic Trouble Codes (DTC) Index >> Ignition System (DTC) Index

Ignition System (DTC) Index

DTC Error Message Diagnostic Procedure Malfunction Criteria and Threshold Value Secondary Parameters with Enable Conditions Monitoring Time Length Frequency of checks, MIL Illum
P0300 crankshaft speed fluctuation (single or multiple) -- Check the Spark plugs.-- Check the intake system for leaks.-- Check the fuel pressure. Refer to FUEL PRESSURE TEST .-- Check the Fuel injectors -N30, N31, N32, N33-. Refer to FUEL INJECTORS, CHECKING .-- Check the Ignition Coils with Power Output Stage -N70, N127, N291, N292-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING .
  • emission threshold misfire rate (MR)> 1.7%
  • catalyst damage misfire rate (MR)> 5.0...20.0%
  • Engine speed range, 440-6800 RPM
  • Engine torque, >=0 Nm
  • ECT > -11° C
  • Fuel cutoff, Not active
  • rough road not detected
  • 1000 Rev.
  • 200 Rev.
  • 2 DCY
  • immediately
P0301  crankshaft speed fluctuation (single or multiple) -- Check the Spark plugs.-- Check the intake system for leaks.-- Check the fuel pressure. Refer to FUEL PRESSURE TEST .-- Check the Fuel injectors -N30, N31, N32, N33-. Refer to FUEL INJECTORS, CHECKING .-- Check the Ignition Coils with Power Output Stage -N70, N127, N291, N292-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING .
  • emission threshold misfire rate (MR)> 1.7%
  • catalyst damage misfire rate (MR)> 5.0...20.0%
  • Engine speed range, 440-6800 RPM
  • Engine torque, >=0 Nm
  • ECT > -11° C
  • Fuel cutoff, Not active
  • rough road not detected
  • 200 Rev.
  • 2 DCY
  • immediately
P0302  crankshaft speed fluctuation (single or multiple) -- Check the Spark plugs.-- Check the intake system for leaks.-- Check the fuel pressure. Refer to FUEL PRESSURE TEST .-- Check the Fuel injectors -N30, N31, N32, N33-. Refer to FUEL INJECTORS, CHECKING .-- Check the Ignition Coils with Power Output Stage -N70, N127, N291, N292-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING .
  • emission threshold misfire rate (MR)> 1.7%
  • catalyst damage misfire rate (MR)> 5.0...20.0%
  • Engine speed range, 440-6800 RPM
  • Engine torque, >=0 Nm
  • ECT > -11° C
  • Fuel cutoff, Not active
  • rough road not detected
  • 200 Rev.
  • 2 DCY
  • immediately
P0303  crankshaft speed fluctuation (single or multiple) -- Check the Spark plugs.-- Check the intake system for leaks.-- Check the fuel pressure. Refer to FUEL PRESSURE TEST .-- Check the Fuel injectors -N30, N31, N32, N33-. Refer to FUEL INJECTORS, CHECKING .-- Check the Ignition Coils with Power Output Stage -N70, N127, N291, N292-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING .
  • emission threshold misfire rate (MR)> 1.7%
  • catalyst damage misfire rate (MR)> 5.0...20.0%
  • Engine speed range, 440-6800 RPM
  • Engine torque, >=0 Nm
  • ECT > -11° C
  • Fuel cutoff, Not active
  • rough road not detected
  • 200 Rev.
  • 2 DCY
  • immediately
P0304  crankshaft speed fluctuation (single or multiple) -- Check the Spark plugs.-- Check the intake system for leaks.-- Check the fuel pressure. Refer to FUEL PRESSURE TEST .-- Check the Fuel injectors -N30, N31, N32, N33-. Refer to FUEL INJECTORS, CHECKING .-- Check the Ignition Coils with Power Output Stage -N70, N127, N291, N292-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING .
  • emission threshold misfire rate (MR)> 1.7%
  • catalyst damage misfire rate (MR)> 5.0...20.0%
  • Engine speed range, 440-6800 RPM
  • Engine torque, >=0 Nm
  • ECT > -11° C
  • Fuel cutoff, Not active
  • rough road not detected
  • 200 Rev.
  • 2 DCY
  • immediately
P0321 Ignition/Distributor Engine Speed Input Circuit Range/Performance -- Check the Engine Speed (RPM) Sensor -G28-. Refer to ENGINE SPEED SENSOR, CHECKING .
  • counted teeth versus reference, incorrect
  • OR
  • monitoring reference gap, failure
 --- 0.50 Sec
  • multiple"
  • 2 DCY
P0322 Ignition/Distributor Engine Speed Input Circuit No Signal -- Check the Engine Speed (RPM) Sensor -G28-. Refer to ENGINE SPEED SENSOR, CHECKING .
  • camshaft signals >3
  • Engine speed, no signal
 --- 0.50 Sec
  • multiple"
  • 2 DCY
P0324 Knock Control System Error -- Check the Knock Sensors -G61-. Refer to KNOCK SENSOR 1, CHECKING .
  • signal fault counter (combustion), >24.0
  • OR
  • signal fault counter (measuring window), >2.00
 engine speed, > 2500 RPM
  • 0.5 Sec
  • Continuous
  • 2 DCY
P0327 Knock Sensor 1 Circuit Low Input (Bank 1) Short to ground, Port B -- Check the Knock Sensor -G61-. Refer to KNOCK SENSOR 1, CHECKING . Lower threshold, <0.70 V
  • Engine speed, > 1000 RPM
 0.5 Sec
  • Continuous
  • 2 DCY
P0327 Knock Sensor 1 Circuit Short to ground, Port A -- Check the Knock Sensor -G61-. Refer to KNOCK SENSOR 1, CHECKING . Lower threshold, <0.70 V
  • Engine speed, > 1000 RPM
 0.5 Sec
  • Continuous
  • 2 DCY
P0327 Knock Sensor 1 Circuit signal range check -- Check the Knock Sensor -G61-. Refer to KNOCK SENSOR 1, CHECKING . Lower threshold, <0.70 V
  • Engine speed, > 1000 RPM
  • ECT >40° C
  • engine load, >23.734...55.172%
 ---
  • Continuous
  • 2 DCY
P0328 Knock Sensor 1 Circuit signal range check (Bank 1) -- Check the Knock Sensor -G61-. Refer to KNOCK SENSOR 1, CHECKING . upper threshold > 18.0...150.0V
  • Engine speed, > 2000 RPM
  • ECT, > 41° C
  • Engine load, > 35.3...60.0%
 0.5 Sec
  • 2 DCY
P0328 Knock Sensor 1 Circuit short to B+ Port B (Bank 1) -- Check the Knock Sensor -G61-. Refer to KNOCK SENSOR 1, CHECKING . upper threshold >1.00 V engine speed >1000 RPM 0.5 Sec
  • Continuous
  • 2 DCY
P0328 Knock Sensor 1 Circuit short to B+ Port A (Bank 1) -- Check the Knock Sensor -G61-. Refer to KNOCK SENSOR 1, CHECKING . upper threshold >1.00 V engine speed >1000 RPM 0.5 Sec
  • Continuous
  • 2 DCY
P0340 Camshaft Position Sensor A Circuit (Bank 1 or single sensor) -- Check the Camshaft Position (CMP) Sensor -G40-. Refer to CAMSHAFT POSITION SENSOR, CHECKING . Cam adaption values out of range
  • >20 ° KW
  • <-20 ° KW
  • Difference of adapted and actual values >9° KW
  • Engine speed sensor, No DTC
  • Phase sensor, No DTC
  • Cam adaptation, Active
  • Engine speed sensor, No DTC
  • Phase sensor, No DTC
  • Camshaft adjustment, No DTC
  • Engine start, Completed
  • Cam adaptation, Completed
  • Camshaft in ref pos. for >2 sec.
 2 Sec
  • 2 DCY
P0341 Camshaft Position Sensor A Circuit Range/Performance (Bank 1 or single sensor) -- Check the Camshaft Position (CMP) Sensor -G40-. Refer to CAMSHAFT POSITION SENSOR, CHECKING . signal pattern, incorrect ---- 0.50 Sec
  • Continuous
  • 2 DCY
P0342 Camshaft Position Sensor A Circuit Low Input (Bank 1 or single sensor) -- Check the Camshaft Position (CMP) Sensor -G40-. Refer to CAMSHAFT POSITION SENSOR, CHECKING .
  • signal voltage low and crankshaft signals, 8.0
 --- 0.50 Sec
  • Continuous
  • 2 DCY
P0343 Camshaft Position Sensor A Circuit High Input (Bank 1 or single sensor) -- Check the Camshaft Position (CMP) Sensor -G40-. Refer to CAMSHAFT POSITION SENSOR, CHECKING .
  • signal voltage high and crankshaft signals, 8.0
 --- 0.50 Sec
  • Continuous
  • 2 DCY
P0351 Ignition Coil A Primary/Secondary Circuit -- Check the Ignition Coils with Power Output Stage -N70-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING .
  • Signal current, < -0.25...2.00 mA
  • OR
  • Internal check, failed
  • Engine speed, >680 RPM
 0.5 Sec
  • Continuous
  • 2 DCY
P0352 Ignition Coil B Primary/Secondary Circuit -- Check the Ignition Coils with Power Output Stage - N127-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING .
  • Signal current, < -0.25...2.00 mA
  • OR
  • Internal check, failed
  • Engine speed, >680 RPM
 0.5 Sec
  • Continuous
  • 2 DCY
P0353 Ignition Coil C Primary/Secondary Circuit -- Check the Ignition Coils with Power Output Stage - N291-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING .
  • Signal current, < -0.25...2.00 mA
  • OR
  • Internal check, failed
  • Engine speed, >680 RPM
 0.5 Sec
  • Continuous
  • 2 DCY
P0354 Ignition Coil D Primary/Secondary Circuit -- Check the Ignition Coils with Power Output Stage -N292-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING .
  • Signal current, < -0.25...2.00 mA
  • OR
  • Internal check, failed
  • Engine speed, >680 RPM
 0.5 Sec
  • Continuous
  • 2 DCY


DTC Error Message Diagnostic Procedure Malfunction Criteria and Threshold Value Secondary Parameters with Enable Conditions Monitoring Time Length Frequency of checks, MIL Illum
P2300 Ignition Coil A Primary Control Circuit Low -- Check the Ignition Coils with Power Output Stage -N70-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING . Signal current >24.0 mA
  • Engine speed, >680 RPM
 0.5 Sec
  • continuous
  • 2 DCY
P2301 Ignition Coil A Primary Control Circuit High -- Check the Ignition Coils with Power Output Stage -N70-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING . Signal current >5.1...7.0 mA
  • Engine speed, >680 RPM
 0.50 Sec
  • continuous
  • 2 DCY
P2303 Ignition Coil B Primary Control Circuit Low -- Check the Ignition Coils with Power Output Stage - N127-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING . Signal current >24.0 mA
  • Engine speed, >680 RPM
 0.50 Sec
  • continuous
  • 2 DCY
P2304 Ignition Coil B Primary Control Circuit High -- Check the Ignition Coils with Power Output Stage - N127-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING . Signal current >5.1...7.0 mA
  • Engine speed, >680 RPM
 0.50 Sec
  • continuous
  • 2 DCY
P2306 Ignition Coil C Primary Control Circuit Low -- Check the Ignition Coils with Power Output Stage -N291-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING . Signal current >24.0 mA
  • Engine speed, >680 RPM
 0.50 Sec
  • continuous
  • 2 DCY
P2307 Ignition Coil C Primary Control Circuit High -- Check the Ignition Coils with Power Output Stage -N291-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING . Signal voltage >5.1...7.0 mA
  • Engine speed, >680 RPM
 ---
  • continuous
  • 2 DCY
P2309 Ignition Coil D Primary Control Circuit Low -- Check the Ignition Coils with Power Output Stage -N292-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING . Signal current >24.0 mA
  • Engine speed, >680 RPM
 0.5 Sec
  • continuous
  • 2 DCY
P2310 Ignition Coil D Primary Control Circuit High -- Check the Ignition Coils with Power Output Stage -N292-. Refer to IGNITION COIL WITH POWER OUTPUT STAGE, CHECKING . Signal voltage >5.1...7.0 mA
  • Engine speed, >680 RPM
 0.5 Sec
  • continuous
  • 2 DCY
scientia non olet · About LEMON Manuals