LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2009 >> S5 Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 887 (Information And Entertainment Systems - 4.2-Inch (107MM) Screen, Am/Fm/Cd/Sync) >> Diagnosis And Testing >> Information and Entertainment System >> Pinpoint Tests >> Pinpoint Test Ab : DTC U0155:00 >> Pinpoint Test Ab : DTC U0155:00

Pinpoint Test Ab : DTC U0155:00

WARNING: This page is about a different car, the 2017 Lincoln Navigator and 2017 Ford Expedition. However, it is still accessible from the selected car via links, so may be relevant.

  1. AB1 VERIFY THE CUSTOMER'S CONCERN

    • Ignition ON.
    • Verify if there is an observable symptom present.

    Is an observable symptom present? 

    Yes  GO to  AB2.
    No  The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  2. AB2 CHECK THE COMMUNICATION NETWORK

    • Using a diagnostic scan tool, perform a network test.

    Does the IPC pass the network test? 

    Yes  GO to  AB3.
    No  REFER to Module Communications Network .

  3. AB3 RETRIEVE THE IPC DTCs

    • Using a diagnostic scan tool, perform the IPC self-test.

    Are any non-network DTCs recorded in the IPC ? 

    Yes  GO to  AB4.
    No  REFER to Multifunction Electronic Modules .

  4. AB4 RECHECK FOR DTC U0155:00

    • Using a diagnostic scan tool, clear all CMDTCs.
    • Ignition OFF.
    • Ignition ON.
    • Wait at least 10 seconds.
    • Using a diagnostic scan tool, retrieve the APIM, ACM, FCDIM, and FCIM CMDTCs.

    Is DTC U0155:00 still set in the APIM, ACM, FCDIM, or FCIM ? 

    Yes  GO to  AB5.
    No  The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  5. AB5 RETRIEVE THE RECORDED DTCs FROM THE APIM, ACM, FCDIM, AND FCIM SELF-TEST

    • Using a diagnostic scan tool, perform the self-test for the following modules:
      • APIM
      • ACM
      • FCDIM
      • FCIM

    Are any non-network DTCs recorded? 

    Yes  REFER to the DTC Charts .
    No  GO to  AB6.

  6. AB6 CHECK FOR DTC U0155 SET IN MULTIPLE MODULES

    • Review the CMDTCs from all modules.

    Is DTC U0155:00 or U0155:87 set in more than one module? 

    Yes  GO to  AB7.
    No  If there is an observable symptom, REFER to the Symptom Charts  to diagnose the observed symptom.If there is no observable symptom, the system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  7. AB7 CHECK FOR CORRECT IPC OPERATION

    • Ignition OFF.
    • Disconnect and inspect the IPC connector.
    • Repair:
      • Corrosion (clean module pins or install new connectors or terminals)
      • Damaged or bent pins (install new terminals or pins)
      • Pushed-out pins (install new pins as necessary)
    • Reconnect the IPC connector. Make sure it seats and latches correctly.
    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable TSBs. If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no TSBs address this concern, APIM Hardware Testing
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals