Diagnostic Mode 01: Obtain data
WARNING: This page is about a different car, the 2009 Audi S6, 2008 Audi S6, and 2007 Audi S6. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostic Mode 01 is used to display and monitor all emissions related measured values.
Test requirement
- Coolant temperature at least 80° C.
Procedure
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Diagnostic Mode 1: Obtain data.".
- From the following table, select the desired the "PID" that is to be monitored, e.g. "PID 05-Coolant temperature".
NOTE:
- More than one "PID" may be selected and monitored.
The current values of the component or system that is being monitored will be displayed on the scan tool screen.
| PID | Description |
|---|---|
| 01: | Number of malfunctions in Mode 3/MIL, Status/Readiness status |
| 03: | Fuel System Status |
| 04: | Calculated load value |
| 05: | Coolant temperature |
| 06: | Oxygen sensor integrator Bank 1/Bank 3 |
| 07: | Oxygen sensor adaptation value Bank 1/Bank 3 |
| 08: | Oxygen sensor integrator Bank 2/Bank 4 |
| 09: | Oxygen sensor adaptation value Bank 2/Bank 4 |
| 11: | Intake manifold pressure |
| 12: | Engine speed |
| 13: | Vehicle speed |
| 14: | Ignition angle cylinder 1 |
| 15: | Intake air temperature |
| 16: | Air mass |
| 17: | Throttle valve position 1 absolute |
| 18: | Secondary air injection |
| 19: | Location of oxygen sensor LSF |
| 20: | LSF sensor voltage Bank 1 Sensor 1, Oxygen sensor integrator Bank 1 |
| 21: | LSF sensor voltage Bank 1 Sensor 2 |
| 22: | LSF sensor voltage Bank 1 Sensor 3 |
| 24: | LSF sensor voltage Bank 2 Sensor 1, Oxygen sensor integrator Bank 2 |
| 25: | LSF sensor voltage Bank 2 Sensor 2 |
| 26: | LSF sensor voltage Bank 2 Sensor 3 |
| 28: | OBD requirements |
| 31: | Time since engine start |
| 32: | Supported definition PIDs 33 - 64 |
| 33: | Distance driven with MIL ON |
| 35: | Fuel pressure (rail pressure) |
| 44: | EGR activation |
| 45: | EGR error |
| 46: | Tank ventilation valve activation |
| 48: | No. of WUCs after erasing DTC memory |
| 49: | Distance driven after erasing DTD memory |
| 51: | Ambient pressure |
| 52: | Oxygen sensor actual value Bank 1 - Sensor 1, Oxygen sensor monitoring pump current Bank 1 - Sensor 1 |
| 56: | Oxygen sensor actual value Bank 2 - Sensor 1, Oxygen sensor monitoring pump current Bank 2 - Sensor 1 |
| 58: | Oxygen sensor actual value Bank 4 - Sensor 1, Oxygen sensor monitoring pump current Bank 4 - Sensor 1 |
| 60: | Catalytic converter temperature Bank 1 Sensor 1 |
| 61: | Catalytic converter temperature Bank 2 Sensor 1 |
| 64: | Supported definition PIDs 65 - 96 |
| 65: | Monitor status in this driving cycle |
| 66: | Control modules system voltage |
| 67: | Absolute load value |
| 68: | Oxygen sensor specified value |
| 69: | Relative throttle valve position |
| 70: | Ambient temperature |
| 71: | Absolute throttle valve position 2 |
| 73: | Absolute accelerator pedal position 1 |
| 74: | Absolute accelerator pedal position 2 |
| 76: | Throttle valve specified position |
| 86: | Offset oxygen sensor control behind cat. Bank 1/Bank 3 |
| 88: | Offset oxygen sensor control behind cat. Bank 2/Bank 4 |
- Switch the ignition off.
- End of diagnosis.