Diagnostic Mode 06 - Checking Test Results of Components Not Continuously Monitored
Mode 06 makes it possible to query test results for special components and systems that are being continuously or not continuously monitored. When the system diagnosis is complete, the results and the associated parameter values are stored in memory and displayed in Mode 06. This data is stored in memory (even when the ignition is off) until either a new diagnostic results are present or if the fault memory is cleared. System Initialization Values (after fault memory has been cleared): Test Results = 0, Test Parameter Values = 0.
| Minimum Value | |
|---|---|
| GST Manual documentation | 0.3499 |
| Aftermarket Scan Tool display | 0.35 |
NOTE:
- Depending on the scan tool and protocol used, the information displayed in Diagnostic Mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), On-Board Diagnostic Monitor Identifier (OBDMID), or contain no name at all and may be referenced by only a number. The min max values for each individual test in Mode 06 represent the min max operating values for a properly operating system. This data is provided to the individual aftermarket scan tool companies for development of their scan tool. Depending on the scan tool being used, the min max values shown may vary, or be rounded up or down to the nearest decimal point depending on the aftermarket scan tool companies development process.
Test requirements
- Exhaust system must be properly sealed between catalytic converter and cylinder head.
- No DTCs in the DTC memory.
- Coolant temperature at least 80 C.
Work procedure
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select the desired "Test-ID"..
The current minimum and maximum values will be displayed on the scan tool screen.
| Test-ID (Hex-ID) | Component or System |
|---|---|
| 01 ($01): | Oxygen Sensor (Bank 1, Sensor 1) |
| 05 ($05): | Oxygen Sensor (Bank 2, Sensor 1) |
| 02 ($02): | Oxygen Sensor (Bank 1, Sensor 2) |
| 06 ($06): | Oxygen Sensor (Bank 2, Sensor 2) |
| 33 ($21): | Catalytic Converter Monitoring Bank 1 |
| 34 ($22): | Catalytic Converter Monitoring Bank 2 |
| 58 ($3A) : | Fuel Tank EVAP System Leak Test (0.090) |
| 59 ($3B): | Fuel Tank EVAP System Leak Test (0.040) |
| 69 ($3C): | Fuel Tank EVAP System Leak Test (0.020/0.5 mm) |
| 61 ($3D): | Tank Vent Valve - Function Check |
| 65 ($41): | Oxygen Sensor Heating in front of Catalytic Converter (Bank 1 - Sensor 1) |
| 69 ($45): | Oxygen Sensor Heating in front of Catalytic Converter (Bank 2- Sensor 1) |
| 66 ($42): | Oxygen Sensor Monitoring Behind Catalytic Converter (Bank 1 - Sensor 2) |
| 70 ($46): | Oxygen Sensor Monitoring Behind Catalytic Converter (Bank 2 - Sensor 2) |
| 162 ($A2): | Combustion Misfire Cylinder 1 Data |
| 163 ($A3): | Combustion Misfire Cylinder 2 Data |
| 164 ($A4): | Combustion Misfire Cylinder 3 Data |
| 165 ($A5): | Combustion Misfire Cylinder 4 Data |
| 162 ($A2): | Combustion Misfire Cylinder 5 Data |
| 162 ($A2): | Combustion Misfire Cylinder 6 Data |
| 11: | Misfire, Averaging over 10 Drive Cycles: |
| 12: | Misfire, in this Drive Cycle |
Test-ID 01 ($01): O2 Sensor in front of Catalytic Converter, (Bank 1- Sensor 1)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 01 ($01)".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 131($83) | P0133 | Response Check. | ---- | > 0.7998 | Refer to DTC P0133 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
| 132($84) | P2195 | Oscillation Check. | --- | > 0.75 V | Refer to DTC P2195 under SAE P2xxx Diagnostic Trouble Codes for all monitoring values. |
| 132($84) | P2196 | Oscillation Check. | --- | 0.15 V | Refer to DTC P2196 under SAE P2xxx Diagnostic Trouble Codes for all monitoring values. |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
Test-ID 05 ($05): O2 Sensor in front of Catalytic Converter, (Bank 2- Sensor 1)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
- Select the desired "Test-ID".
Select "Test-ID 05 ($05)".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
| 131($83) | P0153 | Response Check. | ---- | > 0.7998 | Refer to DTC P0153 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
| 132($84) | P2197 | Oscillation Check. | --- | > 0.75 V | Refer to DTC P2197 under SAE P2xxx Diagnostic Trouble Codes for all monitoring values. |
| 132($84) | P2198 | Oscillation Check. | --- | 0.15 V | Refer to DTC P2198 under SAE P2xxx Diagnostic Trouble Codes for all monitoring values. |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
Test-ID 02 ($02): Oxygen Sensor (Bank 1, Sensor 2)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 02 ($02)".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 129 ($81) | P0138 | Signal activity check. | 0 V | > 1.5 V | P0138 Refer to DTC P0138 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
| 130 ($82) | P0138 | Signal activity check. | 0 V | > 1.5 V | P0138 Refer to DTC P0138 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
| 131($83) | P0138 | Fuel cut off check. | 0 V | > 1.5 V | P0138 Refer to DTC P0138 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
Test-ID 06 ($06): Oxygen Sensor (Bank 2, Sensor 2)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 06 ($06)".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 129 ($81) | P0158 | Signal activity check. | 0 V | > 1.5 V | Refer to DTC P0158 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
| 130 ($82) | P0158 | Signal activity check. | 0 V | > 1.5 V | Refer to DTC P0158 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
| 131($83) | P0158 | Fuel cut off check. | 0 V | > 1.5 V | Refer to DTC P0158 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
Test-ID 33 ($21): Catalytic Converter Monitoring Bank 1
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 33 ($21)".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 132 ($84) | P0421 | Conversion Capability (storage) Check. | --- | > 0.6 | Refer to DTC P0421 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
| 135 ($87) | P0421 | Conversion Capability (storage) Check. | --- | > 0.6 | Refer to DTC P0421 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
Test-ID 34 ($22): Catalytic Converter Monitoring Bank 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
Check Test Results of Components
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 34 ($22): Catalytic Converter Monitoring Bank 2".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 132 ($84) | P0431 | Conversion Capability (storage) Check. | --- | > 0.6 | Refer to DTC P0431 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
| 135 ($87) | P0431 | Conversion Capability (storage) Check. | --- | > 0.6 | Refer to DTC P0431 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
Test-ID 58 ($3A)): Fuel Tank EVAP System Leak Test (0.090)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 03 ($03)".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 129 ($81) | P0455 | Fuel Tank Leak Test | --- | 6.5-0.8 Sec | Refer to DTC P0455 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
Test-ID 59 ($3B)): Fuel Tank EVAP System Leak Test (0.040)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 59 ($3B)".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 129 ($81) | P0442 | Fuel Tank Leak Test | --- | 1.0-1.3 Sec | Refer to DTC P0442 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
Test-ID 60 ($3C) : Fuel Tank EVAP System Leak Test (0.020/0.5mm)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 60 ($3C)".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 130 ($82) | P0456 | Fuel Tank Leak Test. | --- | 4.5-6 Sec | Refer to DTC P0456 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
Test-ID 61 ($3D): Tank Vent Valve - Function Check
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 61 ($3D)".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 128 ($80) | P0441 | Function check. | 0% | 12% | Refer to DTC P0441 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
65 ($41): Oxygen Sensor Heating in front of Catalytic Converter (Bank 1 - Sensor 1)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 65 ($41)".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 133 ($85) | P0135 | Readiness check. | 730° C | > 830° C | Refer to DTC P0135 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
69 ($45): Oxygen Sensor Heating in front of Catalytic Converter (Bank 2 - Sensor 1)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 69 ($45)".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 129 ($81) | P0155 | Readiness check. | 730° C | > 830° C | Refer to DTC P0155 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
66 ($42): Oxygen Sensor Monitoring Behind Catalytic Converter (Bank 1 - Sensor 2)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 66 ($42) ".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 129 ($81) | P0141 | Readiness check. | 0 Ω | > 65535 Ω | Refer to DTC P0141 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
70 ($46): Oxygen Sensor Monitoring Behind Catalytic Converter (Bank 2 - Sensor 2)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 66 ($42) ".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 129 ($81) | P0161 | Readiness check. | 0 Ω | > 65535 Ω | Refer to DTC P0161 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
162 ($A2): Combustion Misfire Cylinder 1 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 162 ($A2): ".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. Max. Values | Additional Information | |
|---|---|---|---|---|---|
| 11 ($0B) | P0301 | Crankshaft speed fluctuation, single or multiple misfire check. | 0 65535 (counts) | Refer to DTC P0301 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. | |
| 12 ($0C) | P0301 | Crankshaft speed fluctuation, single or multiple misfire check. | 0 65535 (counts) | Refer to DTC P0301 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. | |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
163 ($A3): Combustion Misfire Cylinder 2 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 163 ($A3) ".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. Max. Values | Additional Information | |
|---|---|---|---|---|---|
| 11 ($0B) | P0302 | Crankshaft speed fluctuation, single or multiple misfire check. | 0 65535 (counts) | Refer to DTC P0302 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. | |
| 12 ($0C) | P0302 | Crankshaft speed fluctuation, single or multiple misfire check. | 0 65535 (counts) | Refer to DTC P0302 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. | |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
164 ($A4): Combustion Misfire Cylinder 3 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 164 ($A4): ".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. Max. Values | Additional Information | |
|---|---|---|---|---|---|
| 11 ($0B) | P0303 | Crankshaft speed fluctuation, single or multiple misfire check. | 0 65535 (counts) | Refer to DTC P0303 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. | |
| 12 ($0C) | P0303 | Crankshaft speed fluctuation, single or multiple misfire check. | 0 65535 (counts) | Refer to DTC P0303 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. | |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
165 ($A5): Combustion Misfire Cylinder 4 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 165 ($A5): ".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. Max. Values | Additional Information | |
|---|---|---|---|---|---|
| 11 ($0B) | P0304 | Crankshaft speed fluctuation, single or multiple misfire check. | 0 65535 (counts) | Refer to DTC P0304 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. | |
| 12 ($0C) | P0304 | Crankshaft speed fluctuation, single or multiple misfire check. | 0 65535 (counts) | Refer to DTC P0304 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. | |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
166 ($A6): Combustion Misfire Cylinder 5 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 166 ($A6): ".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. Max. Values | Additional Information | |
|---|---|---|---|---|---|
| 11 ($0B) | P0305 | Crankshaft speed fluctuation, single or multiple misfire check. | 0 65535 (counts) | Refer to DTC P0305 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. | |
| 12 ($0C) | P0305 | Crankshaft speed fluctuation, single or multiple misfire check. | 0 65535 (counts) | Refer to DTC P0305 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. | |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
167 ($A7): Combustion Misfire Cylinder 6 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Diagnostic Mode 06 - Checking test results of components that are not continuously monitored".
Select "Test-ID 167 ($A7): ".
- Select the desired "Test-ID".
- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. Max. Values | Additional Information | |
|---|---|---|---|---|---|
| 11 ($0B) | P0306 | Crankshaft speed fluctuation, single or multiple misfire check. | 0 65535 (counts) | Refer to DTC P0306 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. | |
| 12 ($0C) | P0306 | Crankshaft speed fluctuation, single or multiple misfire check. | 0 65535 (counts) | Refer to DTC P0306 under SAE P0xxx Diagnostic Trouble Codes for all monitoring values. | |
- If any component or system fails to meet the specified values, refer to → Diagnostic Mode 03 - Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.
Test-ID (TID) 11: Misfire, Averaging over 10 Drive Cycles
This value is calculated once per drive cycle (after ignition).
Test-ID (TID) 12: Misfire, in this Drive Cycle
This value is updated during the drive. During next ignition the engine misfires from the last drive cycle will be displayed. The TID 12 counter will not be reset until the engine is started.