Section 3 (6.0L - Generic Scan Tool, Engine Code(S): BSB)
WARNING: This page is about a different variant/trim than selected.
- 20 Fuel supply
- Safety Precautions
- Rules for cleanliness
- Fuel supply system components, removing and installing
- Evaporative emissions (EVAP) system
- Electronic power control (EPC)
- 24 Multiport Fuel Injection (MFI)
- Fuel Injection System, Servicing
- Engine components, checking
- Engine Components, Checking
- Oxygen Sensor Heaters Before Catalytic Converter, Checking
- Oxygen Sensor Heaters After Catalytic Converter, Checking
- Mass Air Flow Sensor, Checking
- Throttle Valve Control Modules, Checking
- Coolant Temperature Sensor, Checking
- Intake Air Temperature Sensor, Checking
- Engine Speed Sensor, Checking
- Engine Coolant Temperature Sensor on Radiator, Checking
- MAP Controlled Thermostat, Checking
- Intake System, Checking for Leaks
- Coolant Fan Control Modules, Checking
- Fuel Injectors, Checking
- Fuel Injectors, Checking Injection Quantity and Seal
- Fuel Pressure Regulator and Residual Pressure, Checking
- Functions, Checking
- Engine Control Modules,
- 26 Exhaust system, Emission controls
- Exhaust system components, removing and installing
- Secondary Air Injection System
- Secondary Air Injection System
- Secondary Air Injection, Component Overview
- Secondary Air Injection Combination Valve, Checking
- Secondary Air Injection Pumps, Removing and Installing
- Secondary Air Injection, Left Combination Valve, Removing and Installing
- Secondary Air Injection, Right Combination Valve, Removing and Installing
- Secondary Air Injection Solenoid Valves, Checking
- Secondary Air Injection Pump Motors, Checking
- Combination Valves, Checking
- 28 Ignition/Glow plug System
- Ignition system, servicing
- Ignition System, Servicing
- Safety Precautions
- Ignition System Components, Removing and Installing
- Technical Data, Spark Plugs
- Ignition Coils With Power Output Stage, Removing and Installing
- Ignition Coils With Power Output Stages, Checking
- Terminal Resistance for CAN-Bus, Checking
- Camshaft Position Sensor, Checking
- Knock Sensors, Checking
- Camshaft Adjustment Valves, Checking
- Ignition system, servicing
- 38 - Automatic Transmission - Gears, Hydraulic Controls
- ST Generic Scan Tool
- On Board Diagnostics, general information
- Diagnostic mode, selecting
- Diagnostic Mode, Selecting
- Address Word 33 - On-Board Diagnostic
- Diagnostic Mode 01 - Read Current System Data
- Diagnostic Mode 03 - Read DTC Memory
- SAE Diagnostic Trouble Codes
- Diagnostic Mode 04 - Erase DTC Memory
- Diagnostic Mode 05 - Read Oxygen Sensor Monitoring Test Results
- Diagnostic Mode 05 - Read Oxygen Sensor Monitoring Test Results
- Notes
- Evaluation Test 07 - Minimum Voltage At Sensor for Test Cycle
- Evaluation Test 08 - Maximum Voltage At Sensor for Test Cycle
- Evaluation Test 129 - Oxygen Sensor Value
- Evaluation Test-Id 130 - Control Barrier Value
- Evaluation Test 131 - Dynamic Value
- Diagnostic Mode 6 - Checking Test Results of Components Not Continuously Monitored
- Diagnostic Mode 05 - Read Oxygen Sensor Monitoring Test Results
- Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions
- Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions
- Notes
- Test 01 - Catalytic Converter
- Evaluation test-ID 01: Catalytic converter monitoring
- Test 03 - Secondary Air Injection System
- Evaluation test-ID 03: Secondary air injection (AIR) system
- Test 05 - Tank Ventilation System
- Evaluation test-ID 05: Tank ventilation system
- Test 09 - Engine Coolant Temperature Sensor
- Evaluation test-ID 09: Engine Coolant Temperature (ECT) Sensor G62
- Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions
- Diagnostic Mode 07 - Read Faults Detected During the Current or Last Driving Cycle
- Diagnostic Mode 08 - Request Control of On-Board System, Test or Component
- Diagnostic Mode 09 - Read Vehicle Information
- Readiness code
- Diagnostic Trouble Code (DTC) tables