Drivetrain Control Module (DTCM) - DTCS C207D-68 To C2208-68

• DTC Troubleshooting
  • C207D-68 Monitoring Unit - OVERTEMPERATURE Shutdown
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C207E-64 Monitoring Unit Temperature
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C207F-68 Monitoring Unit - Power Supply Voltage Configuration Check
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2080-68 Can Electrical Failure
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2090-4B Ecu OVERTEMPERATURE Warning
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2091-01 Microcontroller Core - Test Error Event
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2100-68 Operating System Error Event - Error Hook - Shutdown Hook - Unhandled Interrupt
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2101-68 Operating System Memory Protection Error Event
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2102-68 Development Error Tracer Event
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2110-68 SW Module Configuration Invalid
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2111-68 Range Check Failed
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2112-68 Core Exception Of UC - Interrupt Vector Offset Registers
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2117-84 Computing Unit - Temperature Out Of Low Range
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2118-84 Monitoring Unit - Temperature Out Of Low Range
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C211D-68 Kl30 - Kl31 LINEBREAK Error Event
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2121-01 Software Consistency Error Event
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2130-42 Non Volatile Memory Error Event
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2131-42 Flash Error Event
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2132-42 Non Volatile Memory Information Event
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2140-16 Battery Supply Voltage Monitoring
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2140-17 Battery Supply Voltage Monitoring
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2150-68 VIN Mismatch
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2200-64 Transfer Case Fault - Implausible Clutch Wear
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2201-68 Protective Function Powertrain Deactivated
    • When Monitored
    • Set Condition
    • Possible Causes
    • Diagnostic Test
  • C2202-68 Non Volatile Memory Data Corrupt
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2204-68 Transfer Case Fault - Drift Of Initial Position
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2205-98 Maximal Ecu Stress
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2206-68 Transfer Case Fault - Initial Calibration Missing
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2207-68 Transfer Case Fault - Calibration Angle Invalid
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test
  • C2208-68 Transfer Case Fault - Angle Limit Exceed
    • When Monitored
    • Set Condition
    • Default Action
    • Possible Causes
    • Diagnostic Test