LEMON Manuals: Even more car manuals for everyone
Home >> Alfa Romeo >> 2019 >> Giulia Base, AWD >> Repair and Diagnosis >> Engine Performance >> System >> 2.0L - DTCS P0691-00 To P110F-00 >> DTC Troubleshooting >> P105F-00-Humidity Sensor Circuit Out Of Range High >> Diagnostic Test

Diagnostic Test

  1. CHECK FOR AN ACTIVE DTC 
    1. With the scan tool, read Powertrain Control Module (PCM) DTCs and Freeze Frame Data and record on the repair order.
    2. Using the recorded Freeze Frame Data and the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
    3. With the scan tool, read PCM DTCs.

      Is the DTC active or pending?

      Yes 

      • Go To  2

      No 

  2. CHECK THE (K852) 5-VOLT SUPPLY CIRCUIT FOR A SHORT TO VOLTAGE 
    1. Turn the ignition off.
    2. Disconnect the Mass Air Flow (MAF) Sensor harness connector.
    3. Turn the ignition on.
    4. Measure the voltage on the (K852) 5-Volt Supply circuit at the Mass Air Flow (MAF) Sensor harness connector.

      Is the voltage above 5.1 volts?

      Yes 

      No 

      • Go To  3
  3. CHECK THE (K105) HUMIDITY SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE 
    1. Measure the voltage on the (K105) Humidity Signal circuit at the Mass Air Flow (MAF) Sensor harness connector.

      Is the voltage above 5.1 volts?

      Yes 

      No 

      • Go To  4
  4. CHECK THE (K105) HUMIDITY SIGNAL CIRCUIT FOR A SHORT TO ANOTHER CIRCUIT 
    1. Turn the ignition off.
    2. Disconnect the PCM C1 harness connector.
    3. Check for continuity between the (K105) Humidity Signal circuit and all other circuits in the PCM C1 harness connector.

      Is there continuity between the (K105) Humidity Signal circuit and any other circuit?

      Yes 

      No 

      • Go To  5
  5. CHECK THE HUMIDITY SENSOR 
    1. Replace the Mass Air Flow (MAF) Sensor in accordance with the Service Information
    2. Perform the POWERTRAIN VERIFICATION TEST. Refer to PRE-DIAGNOSTIC TROUBLESHOOTING PROCEDURE .
    3. Using the recorded Freeze Frame Data and the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
    4. With the scan tool, read PCM DTCs.

      Is the DTC active or pending?

      Yes 

      • Go To  6

      No 

      • Test complete.
  6. CHECK RELATED PCM AND COMPONENT CONNECTIONS 
    1. Perform any Service Bulletins that apply.
    2. Disconnect all PCM harness connectors.
    3. Disconnect all related in-line harness connections (if equipped).
    4. Disconnect the related component harness connectors.
    5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
      • Proper connector installation.
      • Damaged connector locks.
      • Corrosion.
      • Other signs of water intrusion.
      • Weather seal damage (if equipped).
      • Bent terminals.
      • Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
      • Terminals that have been pushed back into the connector cavity.
      • Check for spread terminals and verify proper terminal tension.

      Repair any conditions that are found.

    6. Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    9. With the scan tool, erase DTCs.
    10. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
    11. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      No 

scientia non olet · About LEMON Manuals